Product center
——
1MW4MWh container energy storage system
The 250KW energy storage system module is composed of a 32kW stack, using a 4-series 2-parallel electrical connection method, with a total of 8 stacks. The system has a DC output voltage of 324-460V and a maximum DC output current of 700A. The 1MW energy storage system is composed of four 250kW energy storage system modules.
Model: YFM2504H YFLO104H Power: 250kW 1000kW Constant capacity: 1000kWh 4000kWh Dc voltage range: 324-460V 324-460V Ac output voltage: 380V 380V Max current: -AC: 500A 2000A Energy efficiency: >75% >70% Communication interface and protocol: RS485,Modbus-RTU RS485,Modbus-RTU Response time: 100ms 100ms Insulation resistance: >550MQ >550MΩ Container Size L×D×H 7689×2.438×2.896m 7.689×2.438×2.896m Overall size 10×8.5×4m 20×17×4m Space requirements 12×10×4.5m 24×20×4.5m Total weight 118t 472t Operating temperature range: -30℃-45℃ -30℃-45℃ Operating humidity: 5%-95% 5%-95%
10KW40KWh all-in-one machine
10kw modular energy storage system 10kW power module Dc output voltage range 40-60V The 1MW energy storage system uses 100 10kW units The modular energy storage system is composed in parallel
10KW reactor

Open circuit voltage                                                                        V              60-75

Maximum charge voltage                                                               V               80

Minimum voltage on discharge                                                       V              57

Maximum charge current                                                                A              160

Maximum discharge current (continuous)                                      A              160

(<300s)Maximum discharge current (< 300s)                             A               175

Continuous power at beginning of discharge                                kW              12

Continuous power at end of discharge                                          kW               8

System Efficiency                                                                                               >80%

Response time                                                                                 ms              < 5

Duty Cycle                                                                                                         100%

Cycle Life                                                                                         cycle          >10000

Service Temperature Range                                                             ℃               0 ~ 40

32kW reactor

Open circuit voltage                                                                        V              96-110

Maximum charge voltage                                                               V                 115

Minimum voltage on discharge                                                      V                  81

Maximum charge current                                                               A                  350

Maximum discharge current (continuous)                                     A                  350

(<300s)Maximum discharge current (< 300s)                           A                  437

Continuous power at beginning of discharge                               kW                37

Continuous power at end of discharge                                         kW                33

System Efficiency                                                                                               >80%

Response time                                                                               ms                 < 5

Duty Cycle                                                                                                            100%

Cycle Life                                                                                        cycle             >10000

Service Temperature Range                                                            ℃                0 ~ 40

Battery management system

The battery management system adopts a two-stage architecture. The lower BMU is responsible for monitoring stack voltage, stack current, relay control, circulating pump control, insulation monitoring, and communicating with the upper BAMS. The upper layer BAMS is responsible for various sensor monitoring of the battery system, battery system balance management, environmental system control, and communication with PCS and intelligent microgrid integrated energy efficiency management platform, while configuring protocol conversion devices to match different protocol requirements.

The battery management system has the following functions: (1) Detect the voltage, current, pressure, temperature, insulation resistance of the stack and the stack group, and carry out real-time monitoring of these parameters, and real-time monitoring of environmental parameters such as temperature and humidity of the container and electrolyte level. (2) Estimate the state of charge (SOC) of the battery and report SOC in real time. (3) Charge and discharge control of the battery according to the state control plan of the battery, such as battery voltage overvoltage or overcurrent, the system immediately stops the battery.

(4) The battery fault diagnosis, and according to the specific fault content of the corresponding fault treatment, with but not limited to the following protection functions: overcharge protection, overdischarge protection, short circuit protection, overload protection, overtemperature protection. Related fault information Provides functions such as uploading fault information and real-time alarm. (5) Real-time monitoring of the reactor and the reactor group of electrolyte temperature, through the heat exchanger to take cooling/heating measures to adjust the temperature of the electrolyte, to prevent all vanadium flow REDOX battery working at high or low temperature. (6) The function of information interaction with the intelligent microgrid integrated energy efficiency management platform.

Vanadium battery electrolyte

The vanadium electrolyte developed by the company has better electrochemical performance, the metal impurity content is obviously better than the national standard grade one, and most of the parameters are better than international standards. 140mA/cm2 current density constant current charge and discharge curve of a single battery. Compared with the original electrolyte, the charging voltage is reduced by 35mV, and the discharge voltage is increased by 90mV, which improves the voltage efficiency of the battery. Compared with the original electrolyte, the new formulation electrolyte will extend the charge and discharge time, for example, the discharge time is extended from the original 38 minutes to 58 minutes, and the performance is improved by 53%.

Property                                                           Unit                                               Specification

Concentration of Vanadium                             mol/L                                                1.0~1.8

Concentration of SO4                                       mol/L                                                3.0~4.5

Average V valence                                                                                                         3.5

Operating Temp                                                  ℃                                                      0~40

Shipping and Storage Temp                                ℃                                                    -25~50

Specific Gravity                                                  g/ml                                                   ≈1.35

5F, Mingjia Business, 18 Shawan Road, Yuhua District, Changsha City, Hunan Province
0731-87193708
Follow us
施秉县| 金华市| 英山县| 留坝县| 仪征市| 安国市| 正镶白旗| 孝昌县| 舞阳县| 屏东市| 鹤壁市| 夹江县| 布尔津县| 上饶市| 永城市| 始兴县| 北宁市| 呼伦贝尔市| 兴安盟| 满洲里市| 突泉县| 镇安县| 许昌县| 班玛县| 广饶县| 尉犁县| 新蔡县| 赫章县| 太和县| 南川市| 昌黎县| 仪征市| 顺昌县| 安阳市| 西平县| 金溪县| 新源县| 栾川县| 新营市| 蒙自县| 长海县|